E9NC-T Contact-Type Smart Sensor/Specifications | OMRON Industrial Automation Singapore

Type	Straight type		E9NC-TH5S	E9NC-TH12S
	Right-angle air type		E9NC-TH5L	E9NC-TH12L
	Flanged type/Straight type		E9NC-TH5SF	E9NC-TH12SF
	Flanged type/Right-angle air type		E9NC-TH5LF	E9NC-TH12LF
Measuring range (Moving range)			5 mm	12 mm
Resolution			0.1 μm
*Precision 1**			1 μm
Measuring force *1	Upward		0.35±0.25 N	0.4±0.3 N
	Horizontal		0.4±0.25 N	0.5±0.3 N
	Downward		0.45±0.25 N	0.6±0.3 N
Indicator (Preamplifier)			Operation indicator (blue/red)
Ambient temperature range			Operating: -10 to 55°C; Storage: -20 to 60°C (with no icing or condensation)
Ambient humidity range			Operating and storage: 35% to 85% (with no condensation)
Maximum response speed			80 m/min
Origin detection speed			80 m/min
Origin position			1 ±0.5 mm from the spindle push-out position (the lowest point)
Vibration resistance (destruction)			100 m/s² (20 to 2,000 Hz) 20 minutes each in X, Y, and Z directions
Shock resistance (destruction)			1,000 m/s² 3 times each in X, Y, and Z directions
Degree of pro- tection	Head	Right-angle air type	IEC IP67 (only when a hose elbow and air hose are connected)
	Head	Straight type	---
	Preamplifier		---
Number of sliding operations			92 million times (based on OMRON’s dedicated evaluation)
Probe			Carbide with a round surface, screw thread size: M2.5
Connecting method			Pre-wired connector (2 m from the Sensor Head to the Preamplifier)
Materials	Sensor Head		Stainless steel (SUS303)
	Rubber boot		Nitrile rubber (NBR)
	Preamplifier		ABS
	*Probe contact point 2**		Carbide
	Cable		PVC
	Hose elbow for air (included) (Right-angle air type only)		Nickel-plated brass
	Tightening nut, Wave washer (Flanged type only)		Tightening nut: Stainless steel (SUS410), Wave washer: SK5
Weight (packed state/Sensor Head only)			Approx. 340 g/approx. 110 g
Accessories			Common: Wrench, Instruction Manual Right-angle air type: Hose elbow Flanged type: Tightening nut, wave washer, clamp wrench, pin

*1. These values were measured at an ambient temperature of 20°C.
*2. For the case of the provided E9NC-TB1 (3-dia. probe)

Type		Communications	ON/OFF output
NPN output		E9NC-TA0	E9NC-TA21
PNP output		E9NC-TA0	E9NC-TA51
Connecting method		Connector for Sensor Communications Unit	Pre-wired type
Inputs/ outputs	Outputs	- *1	2 outputs
Inputs/ outputs	External inputs	- *1	1 input
Power supply voltage		Supplied from the connector through the Sensor Communications Unit	10 to 30 VDC, including 10% ripple (p-p)
Display resolution		0.1 μm min.
*Power consumption 2**		At Power Supply Voltage of 24 VDC Normal mode: 2,040 mW max. (Current consumption: 85 mA max.) Eco ON: 1,800 mW max. (Current consumption: 75 mA max.) Eco LO: 1,920 mW max. (Current consumption: 80 mA max.)
*Control outputs 3**		-	Load power supply voltage: 30 VDC max., open-collector output Load current: 100 mA max. in total for the 2 outputs (Residual voltage At load current of less than 10 mA: 1 V max.,at load current of 10 to 100 mA: 2 V max.) OFF current: 0.1 mA max.
External inputs		-	Refer to *4.
Indicators		7-segment displays (white) GO indicator (orange), HIGH/LOW indicator (orange), NO/NC indicator (orange), PRST indicator (green), ST indicator (blue)
Protection circuits		Power supply reverse polarity protection and output shortcircuit protection	Power supply reverse polarity protection, output short-circuit protection, and output reverse polarity protection
Response time	Super-high-speed mode (SHS)	Operate or reset: 3 ms
	High-speed mode (HS)	Operate or reset: 10 ms
	Standard mode (Stnd)	Operate or reset: 100 ms
	Giga mode (GIGA)	Operate or reset: 1,000 ms
Threshold setting		Smart Tuning (2-point area tuning, tolerance tuning, 2-point tuning, 1-point tuning), or manual adjustment
No. of banks		4
Functions	Output mode selection	Normal output, hybrid output (Output is performed according to the combination of the two bits used to specify HIGH, GO, LOW, and error.)
	Preset	Negative values can be displayed.
	Resetting settings *5	Select from initial reset (factory defaults) or user reset (saved settings).
	*Eco mode 6**	Select from OFF (digital display lit), ECO ON (digital display not lit), and ECO LO (digital display dimmed).
	Bank switching	Select from banks 1 to 4.
	Origin point use setting	Select whether using the Sensor Head origin point or setting the point at power ON as origin.
	Direction	Switchable
	Output	Select from Normal sensing mode or Area sensing mode.
	External input	-	Select from preset, bank switching, input OFF, and tuning.
	Display digits	Settable in units ranging from 0.0001 mm to 1 mm.
	Hysteresis width	-	Select from standard setting or user setting. The hysteresis width can be set to a value from 0 to 9999.9999 in the user settings.
Maximum connectable Units		With E3NW-ECT: 30 units *7 With E3NW-CCL: 16 units	30 units
Ambient temperature range		Operating: Groups of 1 or 2 Amplifier Units: 0 to 55°C, Groups of 3 to 10 Amplifier Units: 0 to 50°C, Groups of 11 to 16 Amplifier Units: 0 to 45°C, Groups of 17 to 30 Amplifier Units: 0 to 40°C Storage: -30 to 70°C (with no icing or condensation)	Operating: Groups of 1 or 2 Amplifier Units: -25 to 55°C, Groups of 3 to 10 Amplifier Units: -25 to 50°C, Groups of 11 to 16 Amplifier Units: -25 to 45°C, Groups of 17 to 30 Amplifier Units: -25 to 40°C Storage: -30 to 70°C (with no icing or condensation)
Ambient humidity range		Operating and storage: 35% to 85% (with no condensation)
Insulation resistance		20 MΩ (at 500 VDC)
Dielectric strength		1,000 VAC at 50/60 Hz for 1 minute
Vibration resistance (destruction)		10 to 55 Hz with a 1.5-mm double amplitude for 2 hours each in X, Y, and Z directions
Shock resistance (destruction)		150 m/s² for 3 times each in X, Y, and Z directions	500 m/s² for 3 times each in X, Y, and Z directions
Weight (packed state/ Amplifier Unit only)		Approx. 65 g/approx. 25 g	Approx. 115 g/approx. 75 g
Materials	Case	Polycarbonate (PC)
	Cover	Polycarbonate (PC)
	Cable	-	PVC
Accessories		Instruction Manual

*1. Two sensor outputs are allocated in the programmable logic controller (PLC) I/O table.
     PLC operation via Communications Unit enables reading detected values and changing settings.
*2. At Power Supply Voltage of 10 to 30 VDC.
     Normal mode: 2,250 mW max. (Current consumption: 75 mA max. at 30 VDC, 155 mA max. at 10 VDC)
     Eco ON: 2,010 mW max. (Current consumption: 67 mA max. at 30 VDC, 135 mA max. at 10 VDC)
     Eco LO: 2,130 mW max. (Current consumption: 71 mA max. at 30 VDC, 145 mA max. at 10 VDC)
*3. Load current: 20 mA max. in total for the 2 outputs when 4 or more units are linked.
*4. The following details apply to the input.

	Contact input (relay or switch)	Non-contact input (transistor)	*Input time4-1**
NPN	ON: Shorted to 0 V (Sourcing current: 1 mA max.). OFF: Open or shorted to Vcc.	ON: 1.5 V max. (Sourcing current: 1 mA max.) OFF: Vcc - 1.5 V to Vcc (Leakage current: 0.1 mA max.)	ON: 9 ms min. OFF: 20 ms min.
PNP	ON: Shorted to Vcc (Sinking current: 3 mA max.). OFF: Open or shorted to 0 V.	ON: Vcc - 1.5 V to Vcc (Sinking current: 3 mA max.) OFF: 1.5 V max. (Leakage current: 0.1 mA max.)	ON: 9 ms min. OFF: 20 ms min.

*4-1.Input time is 25 ms (ON)/(OFF) only when (in tUnE) input is selected.
*5. The bank is not reset by the user reset function or saved by the user save function.
*6. ECO LO is supported for Amplifier Units manufactured in August 2014 or later.
*7. When the Sensors are connected to an OMRON NJ-series Controller.

E9NC-T

Tough Contact Sensor

Sensor Heads

Amplifier Units

Product Category